Product Categories

NK65/25 Needle Roller Bearing — 65 × 78 × 25 mm, Without Inner Ring

Brand:OTOTRI

Product origin:China

Delivery time:3-5 days

Supply capacity:Mass production

NK65/25 machined ring needle bearing without inner ring, 65x78x25 mm. Cr 45 kN, C0r 98 kN, 6000 rpm oil, 221 g, GCr15, 100 pcs MOQ, INA interchangeable.

NK65/25 Needle Roller Bearing — 65 × 78 × 25 mm, Without Inner Ring

NK65/25 is a machined-ring needle roller bearing without an inner ring: 65 mm shaft, 78 mm outside diameter, 25 mm width. It carries 45 kN dynamic and 98 kN static in only 6.5 mm of radial space, at 221 g — the most load-efficient of the three 65 mm-bore options in this series. There is no inner ring because the 65 mm shaft is stiff enough to be the raceway itself, provided it is hardened to 58–62 HRC and ground to Ra ≤ 0.2 µm. GCr15 outer ring, steel cage, from 100 pieces.

Fw65 mmD 78 mmC 25 mmCr45 kN6 000 r/min (oil)221 g

NK65/25 in one paragraph

  1. What it is: a machined-outer-ring needle roller bearing for a 65 mm shaft in a 78 mm housing bore, 25 mm wide — no inner ring, so the shaft is the inner raceway.
  2. Why it wins here: 45 kN in 6.5 mm of radial space at 221 g — 204 kN per kilogram of bearing, against 132 kN/kg for the thicker-walled NKS65. A 65 mm shaft is already stiff, so an inner ring would add mass and buy nothing.
  3. What it demands: a hardened, ground shaft (58–62 HRC, Ra ≤ 0.2 µm, h5). On a soft shaft the 45 kN rating does not apply — the rollers brinell the surface.

NK65/25 Specifications

Designation NK65/25 (catalogue code NK65/25R)
Type Machined ring needle roller bearing, without inner ring, caged
Shaft diameter / raceway Fw 65 mm — the shaft surface is the inner raceway
Outside diameter D 78 mm
Width C 25 mm
Radial space occupied 6.5 mm (=(78 − 65) / 2), rollers included
Corner radius rs min 0.6 mm
Dynamic load rating Cr 45 kN
Static load rating C0r 98 kN
Limiting speed, grease / oil 4 000 / 6 000 r/min
Mass 0.221 kg (221 g)
Outer ring Machined, through-hardened GCr15, ground raceway
Rollers / cage GCr15 needle rollers, steel cage
Shaft requirement 58–62 HRC, case depth ≥ 0.6 mm, Ra ≤ 0.2 µm, h5, roundness IT3
Housing bore H7; N7 if the outer ring rotates or the housing is aluminium
Operating temperature −30 °C to +120 °C
MOQ 100 pcs

Dimensions

NK65/25 · 65 × 78 × 25 mm · shaft acts as the inner racewayshaft ⌀65 (hardened)outer ringmachined GCr15C 25F w6.5radialD ⌀78F w ⌀65Fw 65 mm is the shaft seat, not a bore in the bearing. The dashed circle is the shaft; the rollers run directly on it.

Shaft Requirements — Read This Before Ordering

With no inner ring, the shaft is the raceway. Every load figure here assumes the conditions below. Overload on a 45 HRC shaft does not fail the bearing first — it brinells the shaft, and the bearing follows.

Item Requirement What happens if it is missed
Hardness 58–62 HRC, case depth ≥ 0.6 mm (through-hardened or induction-hardened) Plastic deformation of the raceway; Cr and C0r no longer apply
Surface finish Ra ≤ 0.2 µm, ground — not turned, not rolled Shortened fatigue life; rough peaks act as stress risers
Diameter tolerance h5 (j5 only for light, slow duties) Too loose: the raceway creeps and wears an oval. Too tight: no assembly clearance for the complement
Roundness / cylindricity IT3, straight over the full 25 mm width The complement loads on one side; cage wear and noise
Shoulders Both sides of the outer ring square to the bore within IT5 The machined ring tilts and edge-loads the rollers
Opposite of the HK series. A drawn cup presses into an N7 housing and, being thin, absorbs shaft error. NK65/25 is a stiff machined ring — every micron of shaft error goes into the roller complement.

Same 65 mm Bore, Three Choices

Three ways to fit a 65 mm shaft. The decision is not which is strongest — it is which dimension you are short of.

Model Fw × D × C (mm) Cr / C0r (kN) Grease / oil Mass kN per kg Choose when
NK65/25R 65 × 78 × 25 45 / 98 4 000 / 6 000 0.221 kg 204 Radial space is tight, axial space is available
NK65/35R 65 × 78 × 35 60 / 142 4 000 / 6 000 0.310 kg 194 Same 78 mm bore, 10 mm more width gives +33% dynamic and +45% static
NKS65 65 × 85 × 28 47 / 94 4 000 / 6 000 0.356 kg 132 A 85 mm housing bore is available and you want a thicker ring for shock load

NKS65 shows the trade plainly: 7 mm more outside diameter and 61% more mass buy 2 kN of dynamic load — and slightly less static load. If the bore is fixed at 78 mm, NK65/25 is the answer; widening is almost always cheaper than growing the bore.

NK Series, 50–68 mm Bore

Fourteen sizes around this one, designations exactly as printed in our catalogue. The full NK table is on the NK series size chart.

Model Fw D C Cr / C0r (kN) Grease / oil Mass (kg)
NK50/25RCT 50 62 25 38.5 / 74.5 5 500 / 8 000 0.158
NK50/35R 50 62 35 51 / 106 5 500 / 8 000 0.221
NKS50 50 65 22 31.5 / 57 5 500 / 8 000 0.157
NK55/25R 55 68 25 41 / 82 5 000 / 7 500 0.193
NK55/35R 55 68 35 54 / 118 5 000 / 7 500 0.260
NKS55 55 72 22 33.5 / 63 5 000 / 7 500 0.221
NK60/25R 60 72 25 41 / 85 4 300 / 6 500 0.185
NK60/35R 60 72 35 57 / 130 4 300 / 6 500 0.258
NKS60 60 80 28 44.5 / 85 4 300 / 6 500 0.335
NK65/25R 65 78 25 45 / 98 4 000 / 6 000 0.221
NK65/35R 65 78 35 60 / 142 4 000 / 6 000 0.310
NKS65 65 85 28 47 / 94 4 000 / 6 000 0.356
NK68/25R 68 82 25 44.5 / 89 4 000 / 6 000 0.241
NK68/35R 68 82 35 63 / 139 4 000 / 6 000 0.338

Equivalent Designations

Brand Code Note
INA NK65/25 (X-life: NK65/25-XL) Confirmed 65 × 78 × 25 mm, ≈0.223 kg
SKF / NSK / NTN NK 65/25 Same designation pattern — confirm Fw, D, C and Cr before substituting, as NK boundary dimensions are not fully ISO-standardised
Our code NK65/25R R suffix as printed in our catalogue; state it on the PO to avoid the sealed or NKS variant

Where NK65/25 Is Used

  • Gearbox and reducer intermediate shafts — stiff 65 mm shafts, compact 78 mm housing bore.
  • Hydraulic pumps and motors — 45 kN in 6.5 mm radial space, where the bore is already at its wall limit.
  • Industrial fans and blowers — the 4 000 r/min grease limit covers most direct-drive shafts.
  • Agricultural and construction equipment — 98 kN static absorbs shock that would brinell a drawn cup.

MOQ, Lead Time and Packing

MOQ 100 pcs; stock 3–7 days, production 20–30 days. 10 pcs per VCI bag, 400 per carton, pallet or plywood case, air or sea. Alternative cages and special radial clearance on request — add 5 days for non-stock variants.

Frequently Asked Questions

What is the difference between NK65/25 and an NA-series bearing?

NK65/25 has no inner ring: the 65 mm shaft is the raceway. An NA bearing adds an inner ring, which allows a soft shaft and axial location by shoulders, at the cost of radial space and mass.

Do I need to harden the shaft for NK65/25?

Yes — 58–62 HRC, case depth ≥ 0.6 mm, ground to Ra ≤ 0.2 µm, diameter h5. The 45 kN rating assumes a hardened raceway.

Can NK65/25 be replaced by NK65/35?

Only with 10 mm of extra axial room. NK65/35 shares the 65 × 78 mm envelope and gives 60 / 142 kN instead of 45 / 98 kN, for 89 g more mass.

Need NK65/25, or the 35 mm-wide version?

Send the shaft hardness and finish, the housing bore, the radial load and the speed — we confirm the fit and quote within 24 hours on working days.

Related Products

Consultation